Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I&…
If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly -…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Ford Transit T150 AccessoriesSelect A Category Below
Towing
Ford Transit T150 Trailer Hitch
Ford Transit T150 Trailer Wiring
Ford Transit T150 Brake Controller
Ford Transit T150 Base Plate for Tow Bar
Ford Transit T150 Vehicle Tow Bar Brake System
Ford Transit T150 Vehicle Tow Bar Wiring
Ford Transit T150 BOLT brand vehicle and hitch locks
Cargo Control
Ford Transit T150 Roof Rack
Ford Transit T150 Ladder Rack
Ford Transit T150 Trunk Bike Rack
Performance Accessories
Ford Transit T150 Air Filter
Ford Transit T150 Suspension Enhancement
Ford Transit T150 Performance Chip Tuners
Ford Transit T150 Vehicle Lights
Ford Transit T150 Tire Chains
Ford Transit T150 Fluid Filters
Ford Transit T150 Vehicle Sway Bars
Ford Transit T150 Salt Spreader
Ford Transit T150 Vehicle Engine Heaters
Vehicle Trim
Ford Transit T150 Floor Mats
Ford Transit T150 Nerf Bars - Running Boards
Ford Transit T150 Vehicle Covers
Ford Transit T150 Grille Guard
Ford Transit T150 Mud Flaps
Ford Transit T150 Van Cargo Mat
Ford Transit T150 Truck Tailgate Lock
Ford Transit T150 Vehicle Seat Covers
Ford Transit T150 Windshield Wiper Blades
Ford Transit T150 Windshield Covers
Ford Transit T150 Vehicle Air Mattress
Ford Transit T150 Truck Bed Camera